Software |
? Cisco IOS® Software Release 12.4(21a)JA or later (Standalone Mode)
? Cisco IOS Software Release 12.4(10b) JDD or later (Unified Mode)
? Cisco Unified Wireless Network Software Release 7.0 or later | |||||||
802.11n Capabilities |
? 2x3 MIMO with two spatial streams
? Maximal Ratio Combining (MRC)
? 20-and 40-MHz channels
? PHY data rates up to 300 Mbps
? Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
? 802.11 DFS (Bin 5)
? Cyclic Shift Diversity (CSD) support |
Antenna Connectors |
? 2.4-GHz: 3 RP-TNC connectors
? 5-GHz: 3 RP-TNC connectors | |||||||
Interfaces |
? 10/100/1000BASE-T autosensing (RJ-45)
? Management console port (RJ45) | |||||||
Indicators |
? Status LED indicates operating state, association status, error/warning condition, boot sequence, and maintenance status.
? Ethernet LED indicates activity over the Ethernet, status.
? Radio LED indicates activity over the radio, status. | |||||||
Modularity |
? Number of radio module slots: 2
? Available radio modules | |||||||
Part Number | Description | Maximum per AP1250 platform | ||||||
AIR-RM1252A-x-K9 | 2.4 802.11a/n-d2.0 5-GHz Radio Module; 3 RP-TNC | 1 | ||||||
AIR-RM1252G-x-K9 | 802.11g/n-d2.0 2.4-GHz Radio Module; 3 RP-TNC | 1 | ||||||
Dimensions (W x L x H) |
? AP (without mounting bracket): 8.12 x 9.52 x 2.35 in. (20.62 x 24.18 x 5.97 cm)
? AP (with mounting bracket): 8.12 x 9.52 x 2.75 in. (20.62 x 24.18 x 6.99 cm) | |||||||
Weight |
? AP with 2 radios installed: 5.1 lbs (2.31 kg)
? AP chassis: 2.1 lbs (0.95 kg)
? 2.4 GHz radio: 1.5 lbs (0.68 kg)
? 5 GHz radio: 1.5 lbs (0.68 kg) | |||||||
Environmental | Nonoperating (storage) temperature: -40 to 185°F (-40 to 85°C) Operating temperature: -4 to +131°F (-20 to +55°C) Operating humidity: 10 to 90 percent (noncondensing) | |||||||
System Memory |
? 64 MB DRAM
? 32 MB flash | |||||||
Input Power Requirements |
? AP1250: 36 to 57 VDC
? Power Supply and Power Injector: 100 to 240 VAC; 50 to 60 Hz | |||||||
Powering Options |
? Cisco Catalyst switch port capable of sourcing 20W or greater
? Cisco AP1250 Power Injector (AIR-PWRINJ4)
? Cisco AP1250 Local Power Supply (AIR-PWR-SPLY1)
? 802.3af switch (AP1250 with single radio only) | |||||||
Power Draw |
? AP1250 with two RM1252 radio modules installed: 18.5W
? AP1250 with one RM1252 radio module installed: 12.95W Note: For a 1250 Series Access Point with two radios, 18.5W is the maximum power required at the access point (powered device). When deployed using PoE, the power drawn from the power sourcing equipment will be higher by some amount dependent on the length of the interconnecting cable. This additional power may be as high as 1.5W, bringing the total system power draw (access point + cabling) to 20W. A similar consideration applies for a 1250 Series Access Point with one radio. |
Beschaffenheit: | Neuware |